NextHold Gas to ride away
Left hand · left foot
Key & starter
Right hand · right foot
Everything is asleep
The key is off, so nothing has power.
All live datasimulated values
On the road
Take the Classic out on five Indian roads: a national highway, a ghat with hairpin bends, city traffic, a village road and a road through the forest, or ride all five in one go. Ride freely or take on a challenge. Underneath it is the same simulator as Ride it, so the gearing, torque, grip, ABS and fuel use are the real thing, and the switches, instruments and what-ifs are on the screen.
- Throttle
- 0%
- Economy
- –
- Battery
- 12.7 V
- Trip
- 0.0 km
- Road
- –
- Slope
- flat
- Under the tyres
- dry tarmac
- Limit
- –
A challenge rides the standard bike, so every try is the same. These come back in free ride.
| Gas / brakes (hold) | W / S |
| Front / rear brake only | F / R |
| Steer | A D |
| Shift up / down, neutral | E / Q, N |
| Clutch (Manual) | Space |
| Key / kill switch | K / X |
| Starter (hold) | Enter |
| Side stand | B |
| Beam / pass (hold) | L / J |
| Indicators | , . |
| Horn (hold) | H |
| Hide the switches | I |
| This panel / view / pause | M / V / P |
- Key powers everything: lamps, dash, fuel pump and the engine computer.
- Kill switch on STOP cuts the engine; the key stays on. Set it back to RUN, then hold Start.
- Start only cranks with the key on, the kill switch on RUN and the bike in neutral or the clutch pulled.
- Side stand down with a gear selected cuts the engine, as on the real bike.
- Pass flashes the high beam while you hold it; slower traffic ahead may move over.
Throttle, air and fuel
Twisting the grip does not squirt petrol. It opens a valve that lets the engine breathe. The ECU then works out how much air came in and adds fuel to match.
From your wrist to the cylinder
- Grip to butterfly. The throttle cables turn a pulley on the throttle body. A round plate on a shaft, the butterfly, tilts open. A throttle position sensor on the same shaft reports the angle to the ECU.
- The piston pulls, the throttle limits. On the intake stroke the falling piston drops the pressure in the cylinder. Air rushes in through the snorkel, the paper filter element, the throttle body and the port. Nearly closed, the butterfly chokes the flow and leaves a strong vacuum behind it. Wide open, the manifold sits close to atmospheric pressure.
- The ECU measures. A combined pressure and temperature sensor (T-MAP) tells it how dense the air is. With engine speed from the crank sensor, that gives the mass of air in each cycle.
- Fuel to match. The pump in the tank keeps the injector pressurised. The ECU holds the injector open for a few milliseconds per cycle: a longer pulse means more petrol. It aims for 14.7 g of air per 1 g of petrol, and richer (about 13:1) at full throttle for power and cooling.
Tricks the ECU plays
- Closed loop. An oxygen sensor in the exhaust reports whether the last bang was rich or lean, and the ECU trims the next pulses. That is why the air–fuel ratio wobbles around 14.7 when you cruise.
- Fuel cut on overrun. Shut the throttle above about 1,900 rpm and the injector can stop completely. The wheel is now turning the engine, and that drag is engine braking.
- No choke. A cold engine needs a richer mix. The ECU reads engine temperature and adds fuel by itself, which is why an injected bike has no choke lever.
- Holding idle. With the throttle shut, a small bypass of air keeps the engine alive. The ECU trims it to hold idle near 1,050 rpm and opens it further if you load the engine.
The four-stroke single
One cylinder, 349 cc, two valves and a single overhead camshaft. The crank turns twice for every power stroke, and that slow, heavy rhythm is the famous thump.
The numbers that make it a thumper
Displacement is the volume the piston sweeps: π ÷ 4 × 7.2² × 8.58 cm = 349.3 cc. The stroke is longer than the bore, a long-stroke layout that favours torque at low revs over high-rpm power.
At idle the plug fires 8.75 times a second (1,050 rpm ÷ 120). You can hear each one. At the 6,100 rpm power peak it is 51 times a second and the average piston speed is 17.4 m/s.
Keeping it smooth, cool and oiled
Balancer shaft. A single piston flying up and down shakes the whole engine. The J-series carries a primary balancer: a shaft geared to the crank that spins the opposite way with an offset weight, cancelling most of that shake. Switch it off in Fig 3.1 to feel the difference.
Oil. Wet sump, forced lubrication. About 1.7 litres of 15W-50 semi-synthetic sits in the bottom of the crankcase. A pump pushes it to the crank bearings, camshaft and rockers.
Cooling. Air flowing over the fins carries heat away, helped by oil circulating through the head. That is what air-oil cooled means.
Clutch, gearbox and chain
The engine makes useful torque between about 1,500 and 6,500 rpm, but the rear wheel has to turn at anything from walking pace to 114 km/h. The clutch connects the two gently, five gears pick the right multiplication, and the chain carries it to the wheel.
Assist and slipper ramps
Current dual-channel ABS versions of the Classic 350 use an assist & slipper clutch. Angled ramps sit between the clutch hub and the pressure plate.
Assist: under drive, the ramps pull the pressure plate in, so the plates clamp harder. The springs can be softer, and the lever is lighter.
Slipper: on a hurried downshift the rear wheel tries to spin the engine up. The ramps push the pressure plate out, the clutch slips, and the rear tyre does not hop or lock. Try it in the Ride tab with the Slipper switch off.
How a shift happens
All five pairs of gears stay meshed all the time. Most of them spin freely on their shaft. To select a gear, a fork slides a gear with dogs (stubby teeth on its side) along its splines until the dogs lock into the neighbouring gear. Now that pair carries the power.
Your foot rotates a shift drum one click at a time. Curved grooves in the drum move the forks, which is why the box is sequential: 1, N, 2, 3, 4, 5.
Ratios on the Classic 350
Primary drive 2.313 : 1 · final drive 15/42 teeth = 2.8 : 1 · 104-link chain · rear tyre 120/80-18. Speeds are theoretical, before wind resistance. The real top speed of about 114 km/h is set by drag in 5th.
Brakes and ABS
Brakes turn speed into heat. Hydraulics turn a light squeeze at the lever into kilonewtons of clamp at the disc, and ABS keeps either wheel from locking.
What the ABS unit does
A toothed tone ring on each wheel passes a sensor, so the ABS computer always knows how fast each wheel is turning. If a wheel slows much faster than the bike (it is about to lock), the unit closes the inlet valve and opens the outlet valve to dump pressure, then reapplies it. That cycle repeats several times a second, and you feel it as a buzz in the lever.
The ABS lamp lights when you switch on and goes out once the bike passes 5 km/h and the self-check passes.
Fig 5.2 · Results
| Run | Setup | Distance | Time | Wheels |
|---|
Full lever and pedal, applied in a quarter of a second, clutch pulled. Rider plus bike 270 kg. Compare ABS on and off on wet tarmac, then on gravel: a sliding tyre can push up a wedge of stones and stop shorter, but it cannot steer.
Why the front brake is bigger
When you brake, the bike's mass wants to keep going. Because the centre of mass sits about 0.6 m above the road, that pushes the front tyre down and lifts load off the rear. A tyre's grip grows with the load on it, so the front can deliver far more stopping force.
That is why the Classic 350 has a 300 mm disc with a twin-piston caliper at the front and a 270 mm disc with a single piston at the rear. Base variants with single-channel ABS use a 153 mm drum at the rear instead, and only the front wheel has ABS.
Electrics and starting
A 12 V, 8 Ah battery wakes the ECU, primes the fuel pump and spins the starter. Once the engine runs, the alternator takes over, powering everything and recharging the battery.
The start, step by step
- Key on. The ECU boots, the fuel pump hums for about two seconds to pressurise the line, and the warning lamps light for a self-check.
- Press START. A small current through the button closes the starter relay, which connects the battery straight to the starter motor through a heavy cable. It can draw around 100 A.
- Cranking. The starter turns the crank at a few hundred rpm through a one-way starter clutch. The crank position sensor reads a toothed ring on the flywheel so the ECU can find top dead centre.
- Ignition and injection. The ECU fires the injector and switches the ignition coil. The coil turns 12 V into a spike of tens of kilovolts, which jumps the 0.7–0.8 mm gap at the plug.
- It catches. The engine outruns the starter, the one-way clutch lets go, and the alternator starts charging. Let go of the button.
Interlocks and why it won't start
The engine will crank in neutral, or in gear only with the clutch pulled in. With the side stand down it may start, but it shuts off as soon as a gear is engaged, so you cannot ride off with the stand down.
Suspension and frame
Springs hold the bike up and absorb bumps; dampers stop it bouncing afterwards. The Classic 350 runs 41 mm telescopic forks with 130 mm of travel and twin emulsion shocks with 90 mm of travel and six preload steps.
Spring, damper, preload
Spring: stores the energy of a bump and gives it back. A stiffer spring compresses less but passes more of the jolt through.
Damper: oil squeezed through small holes resists motion and turns the bounce into heat. Without it the bike would pogo for several cycles after every bump.
Preload: the six-step collar on each rear shock compresses the spring before you sit on it. It does not make the spring stiffer. It raises the bike so a pillion does not use up all 90 mm of travel. Set both shocks to the same step.
Test yourself
Ten questions on what you have just seen. Each answer explains the why.
Specification
Published figures for the current J-series Classic 350, from Royal Enfield's technical specification sheet and owner's manual.